Liberty 3 Pro

1) Liberty 3 Pro comes with 4 sizes of ear wings and ear tips. The sizes are: XS(0), S(1), M(2), L(3), and the earbuds come with M(2) ear wings already attached.
2) Select and install the ear tips before using for the first time. We recommend starting with size M(2).
3) Put Liberty 3 Pro in your ears and twist to lock into place. Make sure the ear wings are wedged into the ridge of your ear.
4) Try on different sizes of ear tips and ear wings until you find a combination which delivers a tight seal and snug fit. You may want to use different sizes of ear tips and ear wings in your left and right ears.
5) If you're still not sure about the fit, take the Fit Test in the Soundcore app.

We recommend using ear wings to get the best support and most stable fit. Try using the XS(0) size if the other sizes are all too large.

They are the IR-sensors which sense if the earbuds are currently being worn. If the ear wings are installed incorrectly, the sensor will be covered and it will affect the accuracy of wearing detection. Make sure the ear wings are installed correctly and the surface of the IR-sensors is kept clean.

- Remove one bud to auto pause your media, replace the bud to resume playback.
- Remove two buds to stop your media, and resume playback on your phone manually.
- Auto play/pause may not be compatible with some 3rd party apps.
- You can use the Soundcore app to disable the auto play/pause feature.

Power on:
- The earbuds will turn on automatically when you open the charging case.
- Or long press the touch pad to turn on the earbuds.
Power off:
- Put the earbuds back into the charging case and close the cover to turn off the earbuds.
- The earbuds will also turn off automatically when the earbuds are outside the case, not being worn, and have been disconnected from your device for 30 minutes. (The auto power off time can be customised in the Soundcore app.)
- When you are wearing the earbuds, they will only turn off when the battery runs out.

Yes, just take one earbud out from the charging case to use.
If you are using two earbuds, you can put the earbud you don't want to use in the charging case and continue using the other one on its own.
Note: If you are wearing two earbuds, listening in ANC mode, and you return one earbud to the charging case, ANC will switch to Normal mode automatically because it is not supported. If you wear the second earbud, Normal mode will switch back to ANC automatically.

- To clean the contact pins on both the earbuds and charging case, unplug the charging case from the power, use a cotton swab or cloth dipped in rubbing alcohol, or an alcohol wipe.
- To clean the filter of the earbuds, remove the ear tips first and use a cotton swab dipped in rubbing alcohol to clean.

1) Go to the Apple App Store or Google Play to download the Soundcore app.
2) Pair your device with Liberty 3 Pro.
3) Open the Soundcore app to connect with Liberty 3 Pro.
4) Select "Controls".
5) Customise the controls according to your preferences.
Note: Customised controls are not available when using a single earbud.

Pulsing White: The earbuds are connected via Bluetooth and the pins are connected with the charging case.
Flashing White: The earbuds are in pairing mode.
Rapid Flash 3 Times: The earbuds are resetting.
No Light: The earbuds have not connected correctly with the charging case, or the case has run out of battery.

Long press the left/right earbud to switch between ANC and Transparency modes.
To customise any touch control, download the Soundcore app and go to "Controls".

Take the HearID ANC test in the app. It needs to be conducted in a noisy environment to ensure the best results.
Tips:
- Do not play music while taking the test as it will affect the accuracy of the result.
- Do not swallow or talk during the test.
- External noises need to of a stable level because large fluctuations in noise will affect the accuracy of the results.

Go to "Controls" in the Soundcore app, and choose a custom command for voice assistants.

1) Make sure you are wearing the earbuds correctly.
2) Try single press, double press, long-press, etc. to see if any of the commands work.
3) Reset the earbuds. See "How do I reset Liberty 3 Pro ?" under the Bluetooth tab.

1) Use the earbuds regularly to avoid over-discharge which can harm the lifespan of the earbuds' battery. We recommend using Liberty 3 Pro at least once a month.
2) Charge the earbuds after you use them. In order to improve the battery's lifespan, do not always wait until there's 20% power remaining or less to charge them.
3) If you are storing the charging case, make sure there are at least 2 lights lit up on the case to ensure there is enough power.
4) Open the charging case's lid at least once a month to ensure the earbuds start charging.
5) Regularly clean the charging pins on the earbuds and charging case.
6) Keep the ear tips clean.
7) If it comes into contact with liquid, use a hairdryer on the 'cool' setting to dry the case.

Open the charging case lid so the earbuds enter pairing mode. Pair the earbuds with the first device, wear the earbuds, and then use one of the following methods to pair the second device:
Method 1: Long press both touch pads for 5 seconds until you hear a tone to indicate the earbuds are in pairing mode. Search for Soundcore Liberty 3 Pro in the second device's Bluetooth menu and pair.
Method 2: Use the Bluetooth manager in the Soundcore app to pair a second device or connect to paired device. Notes:
1) To switch between media, you should stop the playing media on the first device, then start playing on the second.
2) The media you're currently listening to will automatically stop when an incoming call is detected. 3) You can turn off the multipoint connection via the Soundcore app.
4) LDAC mode is disabled when using multipoint connection because of the Bluetooth transmission limit.

1) Place the earbuds in the charging case and leave the cover open.
2) Press and hold the button on the case for 10 seconds until the LED indicators inside flash 3 times quickly. When the LEDs start flashing fast, it confirms that the reset was successful and the earbuds have entered pairing mode.

Put the earbuds into the charging case and close for 10 seconds. Then open the case to try pairing again.
If that doesn't work, try the following:
1) Forget the Bluetooth pairing record on your device if you have previously connected the earbuds.
2) Place the earbuds in the charging case and leave the cover open.
3) Press and hold the button on the case for 10 seconds until the LED indicators inside flash 3 times quickly.
When they start flashing fast, it confirms that the reset was successful and the earbuds have entered pairing mode.
4) Turn off your device's Bluetooth and turn it on again to pair with Soundcore Liberty 3 Pro.

Some environments (such as airports, offices, crowded public spaces etc.) can interfere with your Bluetooth connection. To optimise your Bluetooth connection:
1) Ensure your phone is on the right hand side of your body.
2) Download videos and songs instead of streaming.
3) If you have an Android phone, temporarily disable unnecessary app traffic settings on your phone.
Or you can try:
- Resetting the earbuds. See "How do I reset Liberty 3 Pro ?"
- Try a different device if possible.

About 2 hours.

About 4 hours by wireless charger and about 3 hours by USB-C cable.

Normal Mode: Up to 8 hours on a single charge/32 hours with the charging case.
Noise Cancelling Mode: Up to 6 hours on a single charge/24 hours with charging case.
Transparency Mode: Up to 6 hours on a single charge/24 hours with charging case.
Call: Up to 4.5 hours on a single charge/18 hours with charging case.
Data based on internal lab testing. Results may vary under different conditions.

1) Confirm the charging case has power left (press the button on the case and see if a LED is illuminated).
2) Clean the charging pins with a dry cloth and an alcohol-based disinfectant to ensure all charging contact pins on the earbuds and charging case are completely clean and dry of sweat and water. Then put the earbuds into the case correctly. When you put the earbuds back into the charging case, the first and third lights on the case flash twice to indicate both earbuds are charging normally.
3) If they still do not turn on, put the earbuds back into the charging case and close the case for 6 seconds, and then open the case again.

Yes, place the case on the wireless charging pad and make sure it's closed and centrally aligned. If it starts charging you will see the LEDs blinking.

SBC, AAC, and LDAC.

1) Download and update your Soundcore app to latest version.
2. Change the Sound Mode to "Preferred Audio Quality" and follow the instructions to update to the latest firmware version. The LDAC codec is now enabled and will work with your LDAC-compatible device. Note: The LDAC codec processing will increase the power consumption and decrease the overall playtime. Only devices with Android 8.0 or later support LDAC.

Use the Soundcore app to activate 3D Surround Sound. Go to the "Sound Mode" section to switch to 3D Surround Sound.
Note: 3D Surround Sound processes audio data in real time, increasing the power consumption and decreasing the overall playtime.

Here are some tips for enhancing the sound quality and noise cancellation:
1) Try other sizes of ear tips to ensure you're using one that fits well and creates a tight seal.
2) Make sure you're wearing the earbuds in the correct position so that they create a tight seal. To check if you're wearing the earbuds in the perfect position, take the Fit Test on the Soundcore app.
3) Take the HearID ANC test to personalise the noise cancelling effect.
Note: In a noisy environment and at high volume, you may feel that the noise cancellation performance is not as strong.
4) Try different ANC modes to see which one suits your environment best.

Use Wind Reduction mode, which can be found in the ANC section of the Soundcore app. Wind Reduction mode is ideal for environments with constantly high levels of wind, such as cycling, workouts or other outdoor activities. When using this mode, the earbuds will detect wind noise automatically and when it reaches the threshold, Wind Reduction mode starts to work.

Performance improvements and bug fixes:
- Improved usability of touch controls
- AAC/SBC codec audio lag has been reduced
- Improved stability of LDAC mode when playing music
Release Date: 11/20/2021

Performance improvements
- Improved transparency
- Improved call quality for loud, noisy environments
- Improved power management
Release Date: 11/04/2021

- Keep the earbuds in the charging case and ensure the cover is open.
- Make sure the earbuds have enough power (over 20%).
- Do not use the earbuds during the whole process.
- Try again if it fails.