Home/All/
Space One | Active Noise Cancelling Headphones

Space One | Active Noise Cancelling Headphones

  • 2X* stronger voice reduction *Compared with soundcore Life Q30 headphones
  • Reduce noise by up to 98%* with adaptive noise cancelling *Tested by soundcore under laboratory conditions
  • Crisp, Hi-Res sound via 40mm dynamic drivers
  • Worry-free battery (40H ANC on, 55H ANC off)
  • 8° rotating ear cups and soft integrated headband for all-day comfort
  • 5 levels of adjustable transparency to tune your world
  • TCO Certified: For Better Sustainability

color:

$99.99

Same-Day Shipping Underway.

Order Support

Delivery & Payment

Delivery Image

Space One | Active Noise Cancelling Headphones

$99.99

FAQ

Operation Related

How to Switch Ambient Sound Modes

1. Space One automatically sets the default ANC and Transparency levels are both set to 5. These levels can be adjusted through the soundcore app according to personal preference. 2. Pressing the NC button once will switch between noise canceling and transparency modes by default. You can add "normal mode" through the soundcore app, after this, you can press the NC button to cycle through noise canceling, transparency, and normal modes.

How to Reset

To reset the Space One back to factory settings, turn on the headphones and then press and hold the power button and volume up button for 5 seconds. The power indicator light will flash slowly three times in red, indicating that the headphones have been reset to factory settings successfully. Note: After restoring to factory settings, all function switches will be restored to their default settings. For example, after restoring to factory settings, the wear detection function will be restored to the default closed state. Please reset the function switches according to personal usage habits.

How to Switch to BassUp Mode

1. The "Controls" section of the soundcore app allows you to set the double-tap NC button to activate the BassUp feature. After setting, you can experience the BassUp effect by double-tapping the NC button. 2. You can also select the Bass Booster EQ in the soundcore app to experience the BassUp effect.

How to Enable the Wear Detection Function

The automatic play/pause feature (Wearing Detection) is turned off by default. Please remove the dustproof sticker on the sensor detection hole inside the left earpads. Enable the "Wearing Detection" in the upper right corner of the soundcore app to activate the Wearing Detection feature.

Wearing Calibration Related

1. If the Wearing Detection function is not sensitive enough, you can use the wearing calibration feature to improve the sensitivity of the wearing detection. 2. Calibration method: You can perform wearing calibration in the "Wearing Detection" section of the soundcore app's settings menu by following the prompts to restore detection sensitivity. To avoid calibration failure, please pay close attention to the place/wearing guide provided in the souncore app.

How to do Firmware Upgrades

1. You can upgrade the headphone firmware through a pop-up window in the soundcore app. 2. You can also upgrade the firmware in the "Update Firmware" section of the soundcore app's settings menu

Call Control

1. Press the play/pause button once to answer a call 2. Press the play/pause button once to end a call 3. Press and hold the play/pause button for 2 seconds to reject an incoming call 4. During a call, press and hold the play/pause button for 2 seconds to toggle between the mute and unmute states. A prompt tone will indicate a successful switch.

Bluetooth Indicator and Prompt Tone Related Information

1. Power on: Power on tone, battery level voice prompt, power indicator flashes white 3 times and then turns off. 2. Power off: Power off tone, power indicator flashes white 3 times and then turns off. 3. Bluetooth pairing mode: Enters pairing mode with a prompt tone, power indicator flashes blue. 4. Bluetooth pairing success: Bluetooth pairing success tone, power indicator stays on for 3 seconds and then turns off. 5. Bluetooth disconnection: Bluetooth disconnected tone, no light effect. 6. Reconnection mode: Prompt tone, power indicator flashes slowly in blue.

Battery Level Indicator and Prompt Tone Related Information

1. Half an hour before the battery is depleted: Power indicator flashes once every 20 seconds. 2. Charging: Power indicator stays on in red. 3. Fully charged: Power indicator turns off. 4. Battery level below 10%: Power-on prompt for low battery level. 5. Battery level between 31% and 69%: Power-on prompt for medium battery level. 6. Battery level above 70%: Power-on prompt for high battery level.

Play-time Related

Tested battery life data for playing specified music on iPhone at 50% volume: 1. ANC: 40 hours 2. Transparency: 40 hours 3. Normal: 55 hours 4. Fast Charge 5 min: 4 hours under Normal mode.
Connection Related

Bluetooth Connection Related

Bluetooth Connection: 1. If the device has not been paired before, it will enter into pairing mode once activated. Enable Bluetooth on the device you want to connect to, and select "soundcore Space One" from the list. 2. Space One will automatically reconnect to devices previously paired. 3. When the device is turned off, press and hold the Power button for 5 seconds to turn on and enter pairing mode. Wired Connection: 1. Connect Space One to the device using the configured AUX-in cable. By doing this, the Bluetooth function is disabled. Once connected, hold down the power button for roughly 3 seconds to activate Space One. You will hear a audio prompt indicating that the headphones are turned on. Please note in the wired mode, Space One uses the classic EQ. Google Fast Pair: After turning on the headphones or double-clicking the power button to enter pairing mode, simply bring the headphones close to an Android 6.0 phone running Google Play services version 11.7 or higher to quickly connect through a pop-up window.

Multipoint Connection Related

1. With Space One already connected to a device, you can enter multipoint connection mode by double-clicking the power button. From there, follow the standard Bluetooth connection steps to connect a second device. 2. Multipoint connection is enabled automatically. If you wish to change this, connect your Space One headphones with the soundcore app, and select Space One from the "Device List". Here, you can manually deactivate multipoint connecting from the settings menu.

Device Connection Settings

Input and output settings are only required for Bluetooth connections: 1. For Windows computers: Device settings: select "soundcore Space One Hands-Free AG Audio" for input and "soundcore Space One Stereo" for output. For conference software: select "soundcore Space One Hands-Free AG Audio" for both input and output. 2. For macOS computers: Device settings: select "soundcore Space One" for both input and output. For conference software: select "soundcore Space One" for both input and output.
Specifications

Is Space One waterproof and sweatproof?

Due to structural limitations, headband products, especially in areas such as USB and AUX-in, have a high risk of water and sweat ingress. Therefore, the product itself does not have waterproof and sweat-proof characteristics. However, in terms of craftsmanship, UV protection glue technology has been added to the main risk components and key solder points of the internal PCBA to protect these critical areas with UV glue and reduce the risk of the entire machine.
Call Related

Why is the mute icon on the calling software not synchronized with the microphone status of the headphones?

On uncertified calling software, the mute icon of the software will not change with the mute/unmute status of Space One's microphone, but the mute/unmute function on both the software and headphone side can still work normally.

Why is there no change in call sound quality after adjusting the EQ on the soundcore app?

The EQ in the soundcore app only affects media sound quality and has no effect on call sound quality
Troubleshooting Related

What should I do if the volume is not syncing with the device?

1. For some Android phones, the headphone volume is not synchronized by default and users need to manually enter developer mode to adjust the volume synchronization settings. The method of entering developer mode varies depending on the phone model. For most models, you can enter developer mode by going to "Settings", finding the "Phone Version" option, and tapping it repeatedly until a prompt appears indicating that you have entered developer mode. Then, go to "Developer Options" to adjust the absolute volume setting. If this method does not work, you can search online for specific instructions on how to enter developer mode for your particular phone model. 2. For HarmonyOS phones, the headphone volume is not synchronized by default. You can directly enable volume synchronization in the settings window that appears when the Bluetooth connection name is displayed. 3. The media volume and call volume are independent of each other. Therefore, when adjusting the volume during a call, the media volume bar will not change. Similarly, adjusting the media volume bar will not affect the call volume. This does not indicate that the headphone volume is not synchronized with the device.

What should I do if Space One cannot enter multimpoint connection pairing mode?

1. The headphones cannot enter pairing mode during incoming calls or calls in progress. Please try again after ending the call. 2. The headphones cannot enter multipoint connection pairing mode while in LDAC mode. Please exit LDAC mode in the soundcore app settings and try again.

What should I do if reconnection fails?

1. Reboot the device and headphones and try again. 2. On the device, click on the Bluetooth name of the headphones in the Bluetooth list to initiate a Bluetooth reconnection. 3. Select Space One from the list of previously connected devices. 4. Clear the Bluetooth pairing records on the device and put the headphones into pairing mode and try reconnecting. 5. Reset the headphones to factory settings and attempt to pair them with the device again.

What should I do if Space One encounters disconnection issues?

1. Try to shorten the connection distance and avoid any walls or obstacles between the headphones and the device. 2. Rule out the effects of poor network speed or significant environmental interference. You can try switching to a different network or changing the environment where the device and headphones are located to reduce the impact of high-power output interference sources. 3. Rule out the effects of outdated product firmware versions and device system versions. You can try upgrading the headphones firmware and device system version.

What should I do if there is a electrical current sound when connecting to AUX-in cable?

There may be electrical noise when charging the device while using AUX-In cable. It is recommended to unplug the charging cable and only use battery power when using the device, or use a three-pronged grounded plug.

What should I do if I hear calls in poor quality, experience a mic interruption, or no sound from mic?

1. Try selecting the computer as sound input and output and then switching back to the headphones, restarting the headphones, or exiting the call and then re-entering the call to resolve the issue. 2. Confirm that the mic is unmuted, the call software is not muted, and the input settings of the call software are correct. Use the input call detection on the call software to confirm that the device or call software can call the headphones microphone normally. If necessary, you can try restarting the call. 3. If the call quality is poor when using call software, please try to find the following settings in the call app and adjust them: 4. The AUX-in cable does not have a Mic. If it is in a wired connection state, it will use the connected device's own microphone for the call.

What should I do if Space One disconnects, the sound is choppy, or there is no sound?

1. Avoid playing games while on a call. 2. Some phones may have a high power output, which can cause voice distortion or excessive call noise when the headphone volume is too high. It is recommended to reduce the headphone volume appropriately. 3. If it is a software call, try to shorten the connection distance between the headphones and the device, confirm that the input and output selections of the device or call software are correct, switch the output on the call software to the device's built-in speaker and then switch back to the headphones to restore normal call quality. 4. Rule out the impact of poor network speed or excessive environmental interference. You can try switching to a different network connection, and changing the environment where the device and headphones are located to reduce the impact of highpower output interference sources. 5. Rule out the impact of outdated product firmware versions, call software, and device system versions. You can try upgrading the headphones, call software, and device system versions.

What should I do if the sound does not output from the headphones after answering a phone call through a mobile phone?

When headphones are connected to an iOS system phone, if the answer/hang-up button on the headphones is used to answer a call, the phone will select the headphones as the output device. If the call is answered on the phone, the phone's speaker will be selected as the output device. To make the output default to the headphones, go to Accessibility-Touch-Call Audio Routing and select "Bluetooth Headset".

What should I do if the headphones enter the call mode abnormally?

When opening the input/output settings page of the computer system, the headphones will enter into the HFP mode (i.e. call state). Please close the settings page.

What should I do if the sound quality is poor when using Space One?

1. Try to adjust the EQ through the soundcore app to improve sound quality 2. If the headphones are connected to a phone and music is played during a call, the sound quality will deteriorate. Audio transmitted through HFP will cause a decrease in music quality. 3. If the headphones are connected to a computer, opening the input/output settings page of the computer system will put the headphones in call mode. Audio transmitted through the voice channel will cause a decrease in music quality. Please close the settings page. If the computer is running Windows, make sure to select "soundcore Space One Stereo" as the sound output. 4. If the headphones are turned off while connected via AUX-in cable, the classic EQ will not be activated and the sound quality will not be as good. Press the power button to turn on the headphones and activate the music EQ for a better listening experience.

What should I do if the Wearing Detection function fails?

1. Check if Wearing Detection is turned on in the soundcore app. 2. The headphones can only control audio playback apps. Video playback apps may not respond to the music play/pause command sent by the Wearing Detection function. 3. Some devices may not respond properly to the music play/pause command sent by the Wearing Detection function. 4. The Wearing Detection function does not work when connected via AUX-in cable. Please use a Bluetooth connection to experience this function. 5. The Wearing Detection sensor hole is located inside the left earcup. Please make sure there is no hair or clothing blocking the hole when wearing the headphones. When taking off the headphones, flip the left earcup to avoid triggering or mis-triggering the sensor. 6. If the sensor mirror inside the left earcup is dirty or has condensation, it may not work properly. Please use a cotton swab dipped in alcohol to gently wipe it until the dirt and condensation disappear. Please do not wipe it forcefully to avoid scratching the lens and affecting the recognition accuracy. 7. If you manually play or pause audio on the device after taking off the headphones, the audio will not automatically play when you put them back on. If you want to enable automatic play/pause when wearing or taking off the headphones, you need to manually play audio on the device again while wearing the headphones. 8. You can perform wearing calibration in the soundcore app by going to Settings-Wearing Detection-Wearing Calibration in the upper right corner. Please follow the guide images to place and wear the headphones properly to avoid calibration failure.

What should I do if I cannot enter the soundcore app?

When the headphones are connected to two devices at the same time, the soundcore app can only be accessed on one of the devices. Please make sure that the soundcore app is not open on both devices at the same time. If it is, please delete soundcore app from one of the devices and try again.

What should I do if Space One cannot be charged?

1. The headphones can be charged normally when the ambient temperature is between 0-45℃. Please make sure the ambient temperature is within the limited range. 2. The charging current of the headphones is between 530-560mA. An unqualified or faulty charger may have an output power that is too low, causing the output voltage to drop when connected to a high-current device, resulting in the headphones not being charged. Please replace the charger with one that has sufficient power. It is recommended to use a genuine charger with a rating of 5V/1A or higher.
Others

How to better maintain and care for Space One?

1. It is recommended to use the headphones at least once a month to avoid battery depletion and over-discharge, which can affect the battery life. 2. Try to avoid overcharging the headphones. Only charge them when the remaining battery is 20% or less. 3. Place them on a dry, flat surface. If the headphones accidentally get wet, dry them with a hairdryer on the cool setting. 4. It is recommended not to use the headphones in a low-pressure environment. 5. Avoid excessive external force that can cause irreversible damage to the headphones and make them unusable. 6. Sweat has a high salt concentration and is corrosive. Over time, sweat can seep into the leather, causing the leather to weaken and age prematurely. In addition, human skin oils can also damage the leather. Therefore, after use, please clean it with a cotton cloth dipped in 75% medical alcohol and dry it in a ventilated and dry environment. Do not wipe it with water. If it cannot be dried in time, water will accelerate the decomposition of the leather, shortening the life of the leather. 7. Do not use the headphones in a humid environment. Also, try to avoid leaving the headphones unprotected. After using the headphones, let them dry before putting them in a bag or box. The temperature of the place where the headphones are stored should not be too high or too low. Put a desiccant in the bag or box, which can absorb the moisture in the headphones. 8. Exposure to sunlight can accelerate the aging of the leather, so try to avoid storing or using the headphones in this environment. 9. If the ear pads are damaged after their expiration date, please replace them in a timely manner.

How should I deal with foreign objects and liquids entering the charging port?

Be careful to clean up any foreign objects and liquids in the charging port, and let it air dry for 24 hours before charging again.
Documents & Drivers

How to Switch Ambient Sound Modes

1. Space One automatically sets the default ANC and Transparency levels are both set to 5. These levels can be adjusted through the soundcore app according to personal preference. 2. Pressing the NC button once will switch between noise canceling and transparency modes by default. You can add "normal mode" through the soundcore app, after this, you can press the NC button to cycle through noise canceling, transparency, and normal modes.

How to Reset

To reset the Space One back to factory settings, turn on the headphones and then press and hold the power button and volume up button for 5 seconds. The power indicator light will flash slowly three times in red, indicating that the headphones have been reset to factory settings successfully. Note: After restoring to factory settings, all function switches will be restored to their default settings. For example, after restoring to factory settings, the wear detection function will be restored to the default closed state. Please reset the function switches according to personal usage habits.

How to Switch to BassUp Mode

1. The "Controls" section of the soundcore app allows you to set the double-tap NC button to activate the BassUp feature. After setting, you can experience the BassUp effect by double-tapping the NC button. 2. You can also select the Bass Booster EQ in the soundcore app to experience the BassUp effect.

How to Enable the Wear Detection Function

The automatic play/pause feature (Wearing Detection) is turned off by default. Please remove the dustproof sticker on the sensor detection hole inside the left earpads. Enable the "Wearing Detection" in the upper right corner of the soundcore app to activate the Wearing Detection feature.

Wearing Calibration Related

1. If the Wearing Detection function is not sensitive enough, you can use the wearing calibration feature to improve the sensitivity of the wearing detection. 2. Calibration method: You can perform wearing calibration in the "Wearing Detection" section of the soundcore app's settings menu by following the prompts to restore detection sensitivity. To avoid calibration failure, please pay close attention to the place/wearing guide provided in the souncore app.

How to do Firmware Upgrades

1. You can upgrade the headphone firmware through a pop-up window in the soundcore app. 2. You can also upgrade the firmware in the "Update Firmware" section of the soundcore app's settings menu

Call Control

1. Press the play/pause button once to answer a call 2. Press the play/pause button once to end a call 3. Press and hold the play/pause button for 2 seconds to reject an incoming call 4. During a call, press and hold the play/pause button for 2 seconds to toggle between the mute and unmute states. A prompt tone will indicate a successful switch.

Bluetooth Indicator and Prompt Tone Related Information

1. Power on: Power on tone, battery level voice prompt, power indicator flashes white 3 times and then turns off. 2. Power off: Power off tone, power indicator flashes white 3 times and then turns off. 3. Bluetooth pairing mode: Enters pairing mode with a prompt tone, power indicator flashes blue. 4. Bluetooth pairing success: Bluetooth pairing success tone, power indicator stays on for 3 seconds and then turns off. 5. Bluetooth disconnection: Bluetooth disconnected tone, no light effect. 6. Reconnection mode: Prompt tone, power indicator flashes slowly in blue.

Battery Level Indicator and Prompt Tone Related Information

1. Half an hour before the battery is depleted: Power indicator flashes once every 20 seconds. 2. Charging: Power indicator stays on in red. 3. Fully charged: Power indicator turns off. 4. Battery level below 10%: Power-on prompt for low battery level. 5. Battery level between 31% and 69%: Power-on prompt for medium battery level. 6. Battery level above 70%: Power-on prompt for high battery level.

Play-time Related

Tested battery life data for playing specified music on iPhone at 50% volume: 1. ANC: 40 hours 2. Transparency: 40 hours 3. Normal: 55 hours 4. Fast Charge 5 min: 4 hours under Normal mode.
play video

Easy Pack-and-Go

Designed for smooth movement and a symmetrical look. The ear cups rotate and fold neatly for convenient storage.

Contours to Any Head Shape

With the floating design, the ear cups rotate 8° in either direction, effortlessly conforming with high compatibility, for a natural fit.

Long-Listening Made Comfortable

The headband evenly distributes pressure on your head, for gentle support and comfort during prolonged wear.

Sleek, Smooth, and Elegant

Space One combines style with ergonomic design, offering comfort and 3 stunning colors to showcase your flair.

Easy Pack-and-Go

Designed for smooth movement and a symmetrical look. The ear cups rotate and fold neatly for convenient storage.

Compare soundcore Headphones

Space Onesoundcore C40iSpace One ProSpace Q45Life Q30
Space One
soundcore C40i
Space One Pro
Space Q45
Life Q30
Customer Reviews
Active Noise CancellationAdaptive ANC-Adaptive ANC 3.0Adaptive ANCHybrid ANC with Multi-Modes
SoundDetailed Sound, 40mm DriversVibrant Audio, 3D SoundTriple-Composite Drivers40mm Double-Layer DriversRobust Bass, 40mm Silk Drivers
Playtime (ANC Off/On)55H/40H7H/21H with case60H/40H65H/50H60H/40H
Fast Charging5 Mins = 4H10 Mins = 2H5 Mins = 8H5 Mins = 4H5 Mins = 4H
Calls3 mics with AI2 Mics with AI4 mics with AI algorithm2 Mics with AI2 Mics
Multipoint Connection✔️✔️✔️✔️✔️
Customized EQ✔️Hear ID✔️✔️Hear ID 2.0✔️Hear ID✔️
Weight265g (9.35 oz)5.8g (0.19oz)286.2g(10.10 oz)292g (10.30 oz)260g (9.60 oz)
Special FeaturesTravel Pouch, AUXNon-Intrusive Open-Ear Clip-OnSuper Foldable DesignProtective Case, AUXTravel Case, AUX

Customer Reviews

Based on 188 reviews
81%
(152)
16%
(31)
1%
(2)
1%
(1)
1%
(2)
C
Customer
The best headphones I've owned by far!

I had high expectations for these before getting them, but I felt some skepticism due to some critical opinions they have had by time I was about to own them. Using them for the first time, first impressions were very good. The experience was better than expected. First of all, they look better in person, the design of these is interesting; in most angles it has a retro-futuristic and unique look whereas around the top and side profiles it has a more traditionally sleek appearance.
If you pit them next to premium headphones and don't know the brand, you'll have a hard time knowing that this is the "budget headphone". This is due to the overall seamless design combined with the leatherette headband, following the trend from current flagship headphones. When I put them on at first, I had a feeling of pressure in my ears, like I was wearing in-ear headphones; I got used to it quickly.

All features within the app that controls the Space One work really well with a intuitive, user-friendly design. The features don't feel like a gimmick at all, especially the Easy Chat feature; it works either by tapping or talking. When tapping the left earcup it takes about a second to trigger, and as soon as I leave my hand it stops immediately. When talking, the response is instant but in moderate to loud environments it'll have a harder time detecting my voice. Lastly, the Wearing Detection; this pair is the first one I know of that allows you to calibrate it, and it's necessary before using it.

They sound better than I expected, the overall sound presentation is energetic meaning they have an enphasis on bass, and emphasis on the highs.
The emphasis on the former sacrifices the presence in the lower mid range meaning there's an absence of enveloping richness you get from voices and instruments, helping to create sort of an illusion of a speaker in front of you. Despite that, there's still a sense of space thanks to the size of the earcups, the soundstage doesn't feel congested as sound can travel more freely inside the cavity. This means the music doesn't sound congested or trapped in your ears and the sound cues from the tracks are distinguished enough to create an immersive experience.
I created an EQ to make them sound as neutral as possible within hardware limitation; it significantly improves the sound quality and manages to follow the Harman Target Curve.

They are very comfortable, and the fit is the icing on the cake; nice and secure, it doesn't feel unbeareable at all. The seal is really airtight; there's no gaps between the earcups and the sides of my head. It really helps with the noise cancellation as they really reduce ambient sounds when I wear them on the bus or I'm in a place with a lot of people talking at once. Transparency mode works better than I expected, and I found that Easy Chat mode really amplifies the sounds around me. Note that thick hair may interfere with the earcups, which can affect bass and noise cancellation.
I noticed that when using them for the first time the battery lasted less than what Soundcore promised, but when charging and discharging them the first few times the battery performs closer to what they say.

The headphones feel nice and sturdy in the hands but the hinges are kind of flimsy. The left one broke after about four months (keep in mind they were bought a month and a half after release). I took it to a repair shop and they put a screw in the end of the headband and taped it to keep the hinge in place. I had to expand the right hinge all the way to get the best seal possible. Almost five months later, the screw disjointed from the headband which rendered it unusable.

V
Very satisfied
Very very recommended low budget

That is the one cheaper noise cancellation ever if you have low budget i very like it satisfying

D
Diego
Bien por el precio

Cumple con lo prometido

O
Olivia Allen
Sound Quality

I absolutely feel like these headphones are a steal!!! They make enjoying music and videos and podcasts feel so good. I work in a lab and I literally love the noise cancelling feature. I use it when I watch tv through these headphones. At the price point they’re at I would definitely buy them again. I’ve had mine for a few months now and I can successfully say that after tweaking the sound settings to my likings in the app I absolutely will not buy any other headphones until these break or die. They’re also super durable so if you have kids you should get them as well. I don’t have kids but I am 24 and irresponsible with a backpack and they have yet to break.

B
Baked Beans
Great if you have the right expectations

These are great headphones if you have the right expectations. Don't expect these to have amazing sound, Sony level noise canceling, usable call quality in loud environments, gaming-level latency (about 450ms in a rhythm game) , usable wired connection (literal dogwater) and exceptional build materials. Do expect these to be very comfortable, great looks and have features some premium headphones don't even have. Just remember these are $100 budget headphones.Sound quality: Pretty good soundstage and imaging. Quite bassy, can get low and rumble the headphones a bit. Putting any more bass in the EQ makes the bass sound blown out. Recessed mids, though this can be changed though EQ, which is what I did. Highs are good, they've only sounded harsh/sharp in a few very specific songs. The sound quality is acceptable for the price range and can be described as "good". I was used to planar magnetic headphones and IEMs, so the transition took about 3 hours of using them. If you don't like it, you can fiddle around with the EQ, and the drivers will be able to take it. They also get very loud.Build Quality: I don't mind cheap materials as I am a cheapo, but if you aren't, they're probably going to feel slightly cheap (that's because they are). Also, the black color does attract my greasy fingerprints and are visible under a little light.Sound Leakage: There is sound leakage, though not that much. At about 82-84 dB there is enough sound leakage where a person can very slightly hear music 5ft away in a completely silent room. I've used it during school to listen to music and nobody has complained yet.Features: All the features work well, just don't expect them to be the best. For example, easy chat speak to enable can get set off by a person talking next to you in a quiet-ish room. Or if you're speaking quietly In a loud room, it won't pick up your voice. I though the easy chat touch enabled by touch would be good, but it takes a good 2 seconds to respond, so I just ended up using the wear sensor.App: Possibly the best companion app ever for a headphone. A good companion app is very important to me, and it delivers. Customizable infinite EQs, preset EQs, safe volume (which is surprisingly helpful and useful), LDAC, HearID, and more. HearID tests your ears and changes the EQ based on what frequencies you can and can't hear. Very helpful and I use it as my EQ.Other: Battery life is really good and the noise cancelling and transparency modes work well for the price.

Subscribe to our newsletter
for the latest soundcore news, deals, and more.
$10 Gift Card
Members Only
Gift Card Rules:
1. Limitations: Registered users may receive 1 gift card worth $10.
2. Terms of Use: No minimum spend threshold. Can be used with other codes.
3. Timeframe: Must be collected by August 15th, 2024.